Timers : ALGE Comet - Revision history

Geoff: Protected "Timers : ALGE Comet" [edit=sysop:move=sysop]

2009-10-17T01:42:17Z

Protected "Timers : ALGE Comet" [edit=sysop:move=sysop]

← Older revision	Revision as of 20:42, 16 October 2009
(No difference)

Geoff at 01:42, 17 October 2009

2009-10-17T01:42:12Z

← Older revision		Revision as of 20:42, 16 October 2009
Line 1:		Line 1:
	===ALGE Comet===		==ALGE Comet==

	There may be more than one piece of software installed in the comet. You must select either 'Stopwatch' or 'Memo HP' (if your Comet has both choose Memo HP)		There may be more than one piece of software installed in the comet. You must select either 'Stopwatch' or 'Memo HP' (if your Comet has both choose Memo HP)

Geoff at 23:36, 16 October 2009

2009-10-16T23:36:11Z

← Older revision		Revision as of 18:36, 16 October 2009
Line 5:		Line 5:
	To work with the software the Comet must be started with the following set:		To work with the software the Comet must be started with the following set:

	* xxx Times Saved, Clear Y/N ? Y then *		::* xxx Times Saved, Clear Y/N ? Y then *
	* Prog: Stop Select Y/N ? Y then *		::* Prog: Stop Select Y/N ? Y then *
	* Write Sync Time : : Key in the time of day (24 hour format) then press *		::* Write Sync Time : : Key in the time of day (24 hour format) then press *
	* To start clock give a start impulse or press A		::* To start clock give a start impulse or press A

	From this point all inputs are sent as time-of-day directly to the computer (& printer)		From this point all inputs are sent as time-of-day directly to the computer (& printer)

	* Start - Start input via din plug		::* Start - Start input via din plug
	* Finish - Finish input via din plug		::* Finish - Finish input via din plug

	(make sure you get the correct cable from the distributor)		(make sure you get the correct cable from the distributor)

	[[Timers\|back to list of timers]]		[[Timers\|back to list of timers]]

Geoff at 23:35, 16 October 2009

2009-10-16T23:35:41Z

← Older revision		Revision as of 18:35, 16 October 2009
Line 5:		Line 5:
	To work with the software the Comet must be started with the following set:		To work with the software the Comet must be started with the following set:

	* xxx Times Saved, Clear Y/N ? Y then *		* xxx Times Saved, Clear Y/N ? Y then *
	* Prog: Stop Select Y/N ? Y then *		* Prog: Stop Select Y/N ? Y then *
	* Write Sync Time : : Key in the time of day (24 hour format) then press *		* Write Sync Time : : Key in the time of day (24 hour format) then press *
	* To start clock give a start impulse or press A		* To start clock give a start impulse or press A

	From this point all inputs are sent as time-of-day directly to the computer (& printer)		From this point all inputs are sent as time-of-day directly to the computer (& printer)

	* Start - Start input via din plug		* Start - Start input via din plug
	* Finish - Finish input via din plug		* Finish - Finish input via din plug

	(make sure you get the ~~corect~~ cable from the distributor)		(make sure you get the correct cable from the distributor)

	[[Timers\|back to list of timers]]		[[Timers\|back to list of timers]]

Geoff: New page: ===ALGE Comet=== There may be more than one piece of software installed in the comet. You must select either 'Stopwatch' or 'Memo HP' (if your Comet has both choose Memo HP) To work wi...

2009-10-16T23:35:15Z

New page: ===ALGE Comet=== There may be more than one piece of software installed in the comet. You must select either 'Stopwatch' or 'Memo HP' (if your Comet has both choose Memo HP) To work wi...

New page

===ALGE Comet===

There may be more than one piece of software installed in the comet. You must select either 'Stopwatch' or 'Memo HP' (if your Comet has both choose Memo HP)

To work with the software the Comet must be started with the following set:

* xxx Times Saved, Clear Y/N ? Y then *
* Prog: Stop Select Y/N ? Y then *
* Write Sync Time : : Key in the time of day (24 hour format) then press *
* To start clock give a start impulse or press A

From this point all inputs are sent as time-of-day directly to the computer (& printer)

* Start - Start input via din plug
* Finish - Finish input via din plug

(make sure you get the corect cable from the distributor)

[[Timers|back to list of timers]]